[email protected] +86-21-58386189, 58386176

4 Aggregate Specifications and Requirements

Fine Aggregates The fine aggregate, including blended fine aggregate, used in HMA Surface 4.75 mm mixtures is required to have an acid insoluble conten t of not less than 40 percent. For air-cooled blast furnace sl ag or granulated blast furnace slag sand, the acid insoluble content is required to not be less than 25 % for this application.

AASHTO M 6 - Standard Specification for Fine Aggregate for ...

This specification covers the quality and grading of fine aggregate for hydraulic cement concrete used in pavements or bases, highway bridges, and incidental structures. This specification is for use by a contractor, concrete supplier, or other purchaser as part of the purchase document describing the material to be furnished.

MATERIAL SPECIFICATION FOR AGGREGATES - CONCRETE

scaling test according to LS-412 together with either the fine aggregate that the coarse aggregate is intended to be used with, or a fine aggregate from the same geographic area as the coarse aggregate. For the purposes of this specification, the concrete for LS-412 shall be proportioned with 355 kg/m3 of …

Different Types & Sizes of Aggregate for Concrete ...

Aug 11, 2018· [1] FINE AGGREGATE. Fine Aggregates are usually sand or crushed stone that are less than 9.55mm in diameter. When the aggregate is sieved through 4.75mm sieve, the aggregate passed through it. Natural sand is generally used as fine aggregate, silt, …

Standard Specification for Concrete Aggregates

1.1 This specification defines the requirements for grading and quality of fine and coarse aggregate (other than lightweight or heavyweight aggregate) for use in concrete. 2 1.2 This specification is for use by a contractor, concrete supplier, or other purchaser as part of the purchase document describing the material to be furnished.

Sieve Analysis of Fine Aggregates || Procedure and Test ...

Sep 17, 2019· Sieve Analysis of Fine Aggregates – Introduction. Sieve analysis of fine aggregates is one of the most important tests performed on-site. Aggregates are inert materials that are mixed with binding materials such as cement or lime for the manufacturing of mortar or concrete.It is also used as fillers in mortar and concrete. Aggregates size varies from several inches to the size of the ...

What is No-Fines Concrete? Advantages and Mix Proportion

No-Fines Concrete is a lightweight concrete made up of only coarse aggregate, cement and water by omitting fines (sand or fine aggregates) from normal concrete. Advantages, limitations and mix proportions of no-fines concrete is discussed.

2012 Standard Specifications Manual - 10 MATERIALS

Fine aggregate that fails the mortar strength may be used with the approval of the Engineer, provided that when it is tested in concrete cylinders the compressive strength of the concrete at 14 days is equal to or greater than the strength of cylinders made with an identical mix using an acceptable sand.

Difference Between Fine and Coarse Aggregate - Civil ...

Aggregates are essential components of concrete. They act as inert material in concrete. Fine aggregate and coarse aggregate are two main types of aggregate for concrete.As the name indicates, they are basically classified depending on the sizes of aggregate particles.. Fine Aggregate vs Coarse Aggregate

Cement Standards and Concrete Standards

Standard Specification for Concrete Aggregates: C40 / C40M - 20: Standard Test Method for Organic Impurities in Fine Aggregates for Concrete: C70 - 20: Standard Test Method for Surface Moisture in Fine Aggregate: C87 / C87M - 17: Standard Test Method for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar: C88 / C88M - 18

Section 501 Concrete

501.2.5 Aggregates 501.2.5.1 General (1) Furnish material conforming to the individual component requirements of 501.2.5.3 for fine aggregates and 501.2.5.4 for coarse aggregates except as follows: 1. If testing for gradation during concrete production, the department will accept material based on the combined properties as batched.

Aggregates Glossary, Qualified Materials, Engineering

HMA sand (bnk run other surf course) - Unwashed fine aggregate ("bank run") for other than Hot Mix Asphalt surface course. LA - Los Angeles Test for wear, in percent. mixed color glass - Recycled (mixed color) crushed container glass for use in bituminous concrete, when permitted by the specifications.

§501 Section 500 PORTLAND CEMENT CONCRETE

definition of a pozzolan in these specifications. B. Aggregates. Use aggregate from a source on the Approved List of Sources of Fine and Coarse Aggregates that also meets the following requirements for gradation and friction. 1. Gradation. Samples will be taken …

Aggregates for Concrete - GreenSpec

- Fine aggregates are usually sand or crushed stone that are less than 9.55mm in diameter. • Typically the most common size of aggregate used in construction is 20mm. A larger size, 40mm, is more common in mass concrete. • Larger aggregate diameters reduce the quantity of cement and water needed. 20 mm aggregate . Common aggregates ...

What is Concrete Sand Types & Specification - Concrete ...

Uses of Concrete Sand: This is important for using the right type, and better quality of aggregates should be optimized. Two types of aggregates fine and coarse aggregates. Generally compulsion of concrete volume up to 60% to 75%. 70% to 85% by mass the concrete's freshly mixed and hardened mixture proportions & property of real sand and economy.

Fine Aggregate: Definition, Size, Density and Properties ...

Fine aggregate is the essential ingredient in concrete that consists of natural sand or crushed stone. The quality and fine aggregate density strongly influence the hardened properties of the concrete.. The concrete or mortar mixture can be made more durable, stronger and cheaper if you made the selection of fine aggregate on basis of grading zone, particle shape and surface texture, abrasion ...

Minnesota Concrete Flatwork Speci˜cations

a. For any fine aggregate used in curb and gutter, sidewalks, or driveway entrances: the maximum allowable expansion at 14 days is 0.300. b. For any fine aggregate used in concrete pavement, the maximum allowable expansion at 14 days is defined in Table 1 below. If the fine aggregate has been previously tested by MnDOT, use the highest

Section 801 Fine Aggregate

Section 801—Fine Aggregate 801.1 General Description This section includes the requirements for fine aggregate. All aggregate shall be the specified type, class, and grade. 801.1.01 Related References A. Standard Specifications Section 800—Coarse Aggregate Section 441—Miscellaneous Concrete B. Referenced Documents AASHTO ASTM T 11 T 21 T 27

Aggregates for Concrete - Memphis

aggregates cannot be overemphasized. The fine and coarse aggregates generally occupy 60% to 75% of the concrete volume (70% to 85% by mass) and strongly influ-ence the concrete's freshly mixed and hardened proper-ties, mixture proportions, and economy. Fine aggregates (Fig. 5-1) generally consist of natural sand or crushed

Standard Specification for Concrete Aggregates1

TABLE 1 Limits for Deleterious Substances in Fine Aggregate for Concrete Item Mass Percent of Total Sample, max Clay lumps and friable particles 3.0 Material finer than 75-µm (No. 200) sieve: Concrete subject to abrasion 3.0A All other concrete 5.0A Coal and lignite:

Supplemental Specifications

2007 Supplemental Specifications Date Subject (PDF Format) 06/01/2001. Bases & Subbases Quality Control/Quality Assurance ... Gradation of Fine Aggregate FA-10M. 05/21/2008. High Performance Chip Seal. 09/01/2008. ... Fine and Coarse Aggregate for Portland Cement Concrete. 07/01/2019. Sloped Edge Longitudinal Joints. 01/01/2020.

DIVISION 1100 AGGREGATES

1102- AGGREGATES FOR CONCRETE SECTION 1102 AGGREGATES FOR CONCRETE 1102.1 DESCRIPTION This specification is for coarse aggregates, intermediate aggregates, fine aggregates, mixed aggregates (both coarse and fine material) and miscellaneous aggregates for use in all types of concrete construction. 1102.2 REQUIREMENTS a. Coarse Aggregates for ...

SAND EQUIVALENT VALUE SOIL & FINE AGGREGATES (ASTM-D …

Oct 17, 2015· Sand Equivalent Value Test Purpose To determine the percent of undesirable particles in the fine aggregate fraction used in the design of Portland cement concrete mixtures. The method is also applicable for determining the relative proportions of detrimental fine dust or claylike material in soils. Equipment and Materials The Sand Equivalent test kit consists of […]

Garden Guides | ASTM C-33 Specifications

Grading. The C-33 specifications define the grades of quality for both fine and coarse aggregates that are used in concrete. The contractor using the concrete, the concrete supplier or any other purchasers can request evidence of the specifications met to determine the quality of the concrete …

aggregate Topic - concrete.org

May 01, 2020· Aggregates are the major constituent (ingredient) in concrete, making up 60% to 70% of the volume of concrete. Aggregates influence the workability of plastic concrete and also the durability, strength, thermal properties, and density of hardened concrete. Particle size divides aggregates into two categories: fine and coarse. Most fine aggregates are sand and contain particles smaller than 3/8 ...

MATERIAL SPECIFICATION FOR AGGREGATES - …

LS-610 Organic Impurities in Sands for Concrete . LS-614 Freezing and Thawing of Coarse Aggregate . LS-616 Petrographic Analysis of Fine Aggregate . LS-618 Resistance of Coarse Aggregate to Degradation by Abrasion in the Micro-Deval Apparatus . LS-619 Resistance of Fine Aggregate to Degradation by Abrasion in the Micro-Deval Apparatus

specs of fine aggregate for concrete - mensennetwerk.nl

The fine aggregates for concrete having darker color are suspected to have organic impurities and often many specifier or purchaser rejects them at first sight Foundation, Concrete and Earthquake Engineering Foundation, Concrete and Earthquake Engineering, ASTM Specification for Organic Impurities in Fine Aggregate of Concrete